If your WD My Cloud device shows “Local Access Disconnected,” it means the NAS is connected to your network but is not allowing access from computers within the same LAN. This issue is common with models like WD My Cloud, My Cloud Mirror, EX2, or EX2 Ultra, and it can interrupt file sharing, backups, and remote management. The good news is that this problem is usually related to network settings, firmware glitches, IP conflicts, or service configuration.First, confirm that the device is powered on and properly connected to your router via Ethernet cable. Check the LED indicators. A solid blue light usually means the device is ready. If the light is flashing or red, there may be a deeper system or hardware issue. Restart both your router and the WD My Cloud device. Power off the NAS, unplug it for 30 seconds, restart your router, wait until the internet connection stabilizes, and then power the NAS back on. This simple reboot resolves many local access disconnection errors caused by temporary IP conflicts.Next, log in to the WD My Cloud dashboard using its IP address in a browser. If you cannot access it using the device name, open your router’s admin panel and check the connected devices list to find the current IP address. Once inside the dashboard, check whether Network Services such as SMB (Server Message Block) are enabled. SMB is required for Windows file sharing. If it is disabled, local access will not work. Enable SMB and apply the changes.Another common cause is firewall or antivirus software blocking network access. On your computer, temporarily disable firewall or security software and check whether you can access the WD My Cloud shared folders using \IPaddress in Windows Explorer or Finder on Mac. If access works after disabling the firewall, you need to add an exception rule for the NAS device.IP address conflicts can also trigger this issue. If your WD My Cloud is set to DHCP, the router assigns an IP automatically. Sometimes, after a router restart, the IP changes, causing disconnection. To prevent this, assign a static IP address to your NAS either through the router’s DHCP reservation feature or directly in the WD dashboard under network settings.Firmware problems may also cause local access to disconnect. Log in to the dashboard and check for firmware updates. Install the latest firmware version if available. Updated firmware fixes known bugs and improves network stability. However, always back up important data before performing updates.If local access is still disconnected, reset network settings. Use the reset button on the back of the device and hold it for about 4 seconds for a soft reset. This will reset network configurations without deleting data. Avoid performing a full factory reset unless absolutely necessary, as it may erase your data.Also verify that your computer and WD My Cloud are on the same network. If you are using guest WiFi or a different subnet, local access will not work. Both devices must be connected to the same primary network.In some cases, corrupted configuration files or drive health issues may be responsible. Check drive health status inside the dashboard. If the drive shows errors, you may need to run diagnostics or consider replacement.In summary, “Local Access Disconnected” on WD My Cloud is usually related to network configuration, SMB settings, IP changes, firewall blocks, or firmware issues. By systematically checking connections, restarting devices, enabling network services, assigning static IP, and updating firmware, you can restore local access without losing your important data.

Local Access to WD MyCloud disconnected

Connecting to a new network is a common task when you change your WiFi router, move to a new location, or upgrade your internet service. Whether you’re connecting a laptop, smartphone, printer, or other device, the basic steps are similar but may vary slightly depending on the device type.First, make sure your new router is powered on and fully set up. Check that the WiFi name (SSID) and password are ready. These details are usually printed on a sticker on the router or provided by your internet service provider. If you have customized the network name and password, use those instead.On a Windows laptop, click the WiFi icon in the taskbar, select the new network from the list, and click “Connect.” Enter the password carefully, keeping in mind that it is case-sensitive. On a Mac, click the WiFi icon in the top menu bar, choose the new network, and enter the password when prompted. Once connected, test your internet by opening a website.For smartphones and tablets, go to Settings, open WiFi, select the new network, and enter the password. If the device was previously connected to another network, it may automatically switch once the new connection is saved.When connecting devices like printers or smart TVs, access the device’s network or WiFi settings from its control panel. Select the new network name and enter the password using the on-screen keyboard. After connecting, you may need to reconnect the device on your computer as well, especially for wireless printers. In some cases, adding the device again using its IP address ensures a stable connection.If the device fails to connect, double-check the password and confirm you are choosing the correct network. Restarting the router and the device often resolves temporary issues. Also ensure you are within good signal range and that the router supports the device’s WiFi band (2.4GHz is commonly more compatible with older devices).After successfully connecting to a new network, it’s a good idea to remove old saved networks you no longer use. This prevents automatic switching and connection conflicts in the future.

Is there a way to test the fan without SSH?